48 inch solid flooring slabs

Subfloors The National Wood Flooring Association recommends two choices in sub-flooring systems for concrete installations: plywood-on-slab and sleeper. Either subfloor system is satisfactory for three-quarter inch flooring. Plank Flooring Plank flooring four inches and wider requires either the plywood-on-slab system or 

It can be done!! Gluing down prefinished SOLID three quarter inch hardwood flooring directly over a concrete slab Here's the bottom line this can be done! 80% of the research I did on this said it can't be done (including posts on Houzz) or not to attempt it. Well, I'm here to say it can done, h

has your back when it comes to hardwood floors. We offer you different styles of solid or engineered and click hardwood, as well as mouldings.

SUBFLOOR PREPARATION RECOMMENDATIONS FOR ON OR. ABOVE GRADE ONLY: We recommend 3 types of sub-floors: plywood/OSB, solid wood planks (1 x 6 or larger), or sleepers (2 x 4 inch). Each subfloor has separate installation guidelines. Solid hardwood flooring may be installed on or above grade provided.

Single Paving Slabs - B&Q for all your home and garden supplies and advice on all the latest DIY trends.

For residential construction, tendons at 48 inches on center are common. Commercial A residential post-tensioned concrete slab will typically be 8 inches thick and use 3000 psi concrete. Larger structural concrete members may also be post-tensioned, especially in bridges and floors and beams in parking structures.

A plywood core makes engineered flooring the most stable choice, provided the slab is flat and dry. Make sure the compound has a compressive strength greater than 3000 psi (pounds per square inch). After mixing it to the I wait 24 to 48 hours to begin the installation in these areas, just to be safe.

Find great deals on eBay for Marble Slab in DIY Stone Flooring. Shop with confidence. £21.00. 10 bids. £0.00 P&P. 34 watching. Solid White Italian marble slab - large piece 43cm x 183cm x 2cm. grey veins. Very good condition. W x 17 inches L x 48 inches Please ask if you have any questions regarding this item.

Like unfinished hardwood floors, the prefinished types typically have tongue-and-groove edges on all sides. They are available in 3/4-inch thickness, as well as low-profile styles that are 5/16- to 5/8-inch thick, which are a good or installing over existing flooring. Solid wood floors should not be installed in basements or 

Polyfilm — 6- or 8-mil polyethelene film in 36-inch or 48-inch-wide rolls — applied over a "skim" coat of asphalt mastic. The mastic should be troweled with a straightedge trowel to skim coat the slab, with coverage of about 80-100 square feet per gallon. After about 30 minutes, during which the solvents 

Flooring should be at the job site at least 48 hours prior to installation. Do not open the cartons until ready to install. Handle with care. Do not stand cartons on ends or sides. Stack wood flooring flat with proper support on the ends and center sections. Store in a dry place and provide at least a four-inch air space under and 

All about installing hardwood flooring over a radiant heat system. By installing the radiant heat tubing within a plywood underlayment system, directly over the existing concrete slab or existing wood subfloor. . areas of the slab. Wait 48 hours before looking to see if any moisture (condensation) builds up under the sheets.

Paving choice is a big decision as the area is needed to be robust & last. Check out our beautiful natural stone available to order online from Homebase.

Laminate flooring is perfect for anyone wanting a durable floor for a fraction of the price and installation time of a hardwood floor, but with the attractiveness of real hardwood. Laminate is also You must acclimate your laminate boards for 48 hours in the room where they will be installed, before you install them. That means 

Tape a 15-inch square of clear polyethylene film to the slab with moisture-resistant tape, sealing all four edges. If no condensation collects under the film after 24-48 hours, the slab is dry enough for floor installation. Subfloor Options. The National Wood Flooring Association (NWFA) recommends two choices in sub-flooring 

Birch Engineered Hardwood - Penn's Woods. 5 3/4 in. Wide x Varying Lengths: 9 - 48 in. Long x 1/2 in. Thick; Engineered; Low Gloss; Scraped Edge / Micro Ends. Cherry Engineered Hardwood - Amber. Metro Classics4510CA